July 7, 2026
This pair of adapter plates gets you out of the mismatch problem of having a 240mm AIO Radiator and 2x 120mm fans but 2x 140mm case fan slots on the case instead of 120mm fan slots. This pair of flat adapter plates will let you mount into two side by side 140mm fan slots a 240mm AIO radiator with 2 120mm fans sandwiched either way (240mm radiator in the middle or the fans). If, however, you have a 280mm radiator this will not fit it. Have a look at my other listing: https://www.ebay.com/itm/304156777579 Comes with the screws you’ll need; really easy just screw the plates-120mm fans-240mm radiator sandwich together with the long screws and then screw the whole thing into your 140mm fan slots with the fat fan screws. For the other sandwich you additionally use the short #6-32 screws to mount the radiator to the adapter plates. Also comes with 32 spacers* for getting a tight fit in case your fan is too thin or something. Supports center hole spacing on the 240mm radiator between 15mm and 19mm for maximum compatibility. It’s usually 15mm or 16mm. Will fit up to 27mm thick 120mm fans, any thicker you will need your own #6-32 screws longer than 30mm.Also you will need your own long screws if your radiator holes are M3 or something instead of the standard #6-32 (haven’t seen it though). Fits standard 120mm fans, 240mm radiators, and 140mm slots. Will almost certainly fit unless you have a really strange fan; if in doubt refer to the technical drawing and measure your 120mm fans, radiator, and fan slot. Unlike other adapters, this design completely fills in the frame around the smaller 120mm fan so the case is still sealed to air afterwards and your fan works as efficiently as possible providing airflow. If you need an adapter for other sizes to other sizes let me know and I can design one for you. ONLY ONE ADAPTER (2 plates), TWENTY-FOUR (24) SCREWS , AND THIRTY-TWO (32) SPACERS INCLUDED. *Note, all 32 spacers may not be the same color or the matching color to the plates. They cannot be seen once mounted anyhow.
Read More
July 7, 2026
This pair of adapter plates gets you out of the mismatch problem of having a 240mm AIO Radiator and 2x 140mm fans with 2x 140mm case fan slots on the case instead of 120mm fan slots and 120mm fans. These 28mm tall adapter plates smoothly reduce the larger 140mm fan airflow circle to the 120mm size and sandwich between your radiator and fans with the fans mounted to the case and the radiator inwards. It is not possible to sandwich the other way. If, however, you have a 280mm radiator this will not fit it. Have a look at my other listing: https://www.ebay.com/itm/304156777579 Comes with the screws you’ll need; really easy just screw the radiator to the plates with the #6-32 or M4 philips screws using the underneath recessed holes. Then, use the M5 self-tapping screws to attach the adapter plates to the fans and then place the adapters and radiator assemblage to your case fan slots and screw the fans to the case from the outside of the case using the M5 self-tapping fan screws. Supports center hole spacing on the 240mm radiator between 15mm and 19mm for maximum compatibility. It’s usually 15mm or 16mm. Your radiator will sit another 28mm inwards in the case after this – please make sure you have clearance. Also if your radiator holes are M3 or something instead of the standard #6-32 / M4 (haven’t seen it though) you will need your own screws. Fits standard 140mm fans, 240mm radiators, and 140mm slots. Will almost certainly fit unless you have a really strange fan; if in doubt refer to the technical drawing and measure your 140mm fans, radiator, and fan slot. If you need an adapter for other sizes to other sizes let me know and I can design one for you. ONLY ONE ADAPTER (2 plates) AND TWENTY-FOUR (24) SCREWS INCLUDED.
Read More
July 5, 2026
120mm fan to 92mm fan slot adapter. Let’s you mount a larger 120mm fan in a fan slot that can only fit a 92mm fan. Has centered walls that are flush with the 92mm fan slot. If, however, you want to fit a smaller 92mm fan into a slot that only fits a 120mm, then you want my other listing:https://www.ebay.com/itm/304148161982 Choose the height of the adapter so that the larger 120mm fan can sit far enough away from the 92mm slot to get clearance. Usually there are walls of the case or what not close around the 92mm fan slot that would block the larger fan. Take a look at the pictures mounted in case*. Comes with the 8 screws you’ll need; really easy just screw your 120mm fan to the adapter and then the adapter to the case. Fits standard 120mm fans and 92mm slots. Will almost certainly fit unless you have a really strange fan; if in doubt refer to the technical drawing and measure your fan & fan slot. Unlike other adapters, this design completely fills in the frame around the 140mm fan so the case is still sealed to air afterwards and your fan works as efficiently as possible providing airflow. You can also use this to mount both a 120mm fan AND a 92mm fan in a forced air setup into either a 120mm or 92mm fan slot. You will want at least 30mm height in that case since you’ll want a big enough plenum between them. If you need an adapter for other sizes or want another color just message me. ONLY ONE ADAPTER AND EIGHT (8) SCREWS INCLUDED. *DEMO PHOTOS ARE OF THE 140MM TO 120MM FAN SLOT ADAPTER BUT YOU GET THE IDEA.
Read More
July 5, 2026
These are original stock height (25mm) and extended height (45mm tall) feet for the Lian-li O11 Dynamic or O11D ATX case (NOTE, NOT FOR THE Mini version of the O11 Dynamic !!). Let’s you fit a radiator or fans underneath easily. The feet have insets matching the stock rubber pads. Simply unpeel your rubber pads from the original feet and transfer them over to the new feet. These feet will NOT FIT any of the other Lian-Li cases as far as I am aware from checking the look of each model. If you are looking for case feet for the Lian-Li O11D Mini , those are here: https://www.ebay.com/itm/304796852615
Read More
July 5, 2026
These are 4 extended height (30mm tall) feet for the Lian-li TU150 mini-ITX case. Also called the TU150-WX and TU150-WA depending on finish – brushed aluminum or black. These feet let you fit a radiator or fans underneath easily. The stock feet are much shorter – around 15mm. If you need more than 30mm tall just let me know. NOTE – NO SCREWS INCLUDED. It is intended you will use the screws already holding the stock feet. These feet are also designed so that you can move and fit the donut-shaped rubber pads from the original feet. Designed following measurements of originals. Guaranteed to fit a TU150 mini-ITX case or you can return or I will send you feet with corrections made so that they will fit. These feet will NOT FIT any of the other Lian-Li cases as far as I am aware from checking the look of each model.
Read More
July 5, 2026
These are a front and back pair of extended height (30mm tall) feet for the Lian-li “Dan” A4 H2O case. Let’s you fit a radiator or fans underneath easily. The stock feet are much shorter – around 7mm. NOTE – NO SCREWS INCLUDED. These will work with the screws already holding the stock feet. Designed using Lian’s own self-published STEP files (3D model file format) for their A4 H2O case as found linked on the product page for this case on Lian’s website. Guaranteed to fit! These feet will NOT FIT any of the other Lian-Li cases as far as I am aware from checking the look of each model.
Read More
July 5, 2026
THESE WILL NOT FIT THE O11D EVO NON-RGB VARIANT! Extended height (35mm tall) feet (4x) for the Lian-li O11D EVO RGB case. THESE WILL NOT FIT THE NON-RGB VARIANT OR THE EVO XL. Let’s you fit a radiator or fans or bottom mount SSD underneath easily.
Read More
July 5, 2026
These are 4 extended height (40mm tall) feet for the Lian-li O11 Air Mini case. Also called the Air Mini. Let’s you fit a radiator or fans underneath easily. The stock feet are much shorter – around 20mm. NOTE – NO SCREWS INCLUDED. It is assumed you will use the screws already holding the stock feet. Designed using Lian’s own self-published STEP files (3D model file format) for their o11 Air Mini case as found linked on the product page for this case on Lian’s website. Guaranteed to fit! These feet will NOT FIT any of the other Lian-Li cases as far as I am aware from checking the look of each model.
Read More
July 5, 2026
These are taller Cooler Master NR200/NR200P MasterBox mini-ITX case feet – either 40mm or 70mm height. Now you can fit a 120mm fan underneath the case and have a radiator just above the bottom plate of the case. Or get the extra tall 70mm size for even more airflow and space for even a radiator and fan underneath the case. THE BOTTOM RECESS IS IDENTICAL TO STOCK! YOUR STOCK RUBBER PADS WILL FIT! THESE FEET ARE FOR THE MASTERBOX NR200 / NR200P (mini-ITX) – the MAX has slightly different feet with more screw holes! Printed using Cooler Master’s own STL file for the stock design, but modified. Identical top face and bottom recess dimensions, but scaled in the height direction and with extra thick reinforcement walls for the screw hole. Listing is for a set of 4 feet; choose either white or black color as well as what height (40mm or 70mm).
Read More
July 5, 2026
If you have a Lian-Li Lancool 216 case with Lian’s 160mm fans, this pair of adapter plates allows you to mount the 160mm fans to a 240mm AIO radiator. Fits Lian-Li’s 160mm fans ONLY! Not Silverstone.
Read More